Author name: admin

1. Log on as user root.2. Create a mount point for the CD-ROM with the command:mkdir <CD-mountdir> (for example, <CD-mountdir> is /sapcd)3. Mount the CD-ROM with the command:mount -dr -t cdfs /dev/rz<n>c <CD-mountdir><n> is the hardware or SCSI address of the CD-ROM (0-6).If the command fails with the message Invalid argument, the kernel is not […]

When SCSI read and write errors are logged in the syslog, the device number is written in hex. For example: Jun 2 21:13:38 pdb01 vmunix: SCSI: Read error — dev: b 31 0x2b8400, errno: 126, resid: 8192,Jun 2 21:13:39 pdb01 above message repeats 13 timesJun 2 21:13:39 pdb01 vmunix: – dev: b 31 0x2b8400, errno:

1. Create volume group.See the section Creating Volume Groups.2. Create logical volume:a. Enter the command smitty.b. Select: Physical & Logical Storage → Logical Volume Manager → Logical Volumes → Add a Logical Volume c. Enter volume group name.d. Enter logical volume name (for example: lvsap02).e. Enter the number of logical partitions.f. Set the logical volume

1. Create one logical volume for each file system listed in the your profile.a. Select:Physical & Logical Storage → Logical Volume Manager → Logical Volumes → Add a Logical Volumeb. Enter a volume group name, for example, sapr3vg.c. Enter a logical volume name, for example, lvsap01.d. Enter the number of logical partitions (see section Size

The “df -g” command shows it, but apparently not if you are using Veritas file-system; Veritas says they do not support “df -g” So, instead, for VxFS on HPUX, use “/usr/sbin/fstyp -v <special>”, where “<special>” is the block-special device underlying the file-system. # /usr/sbin/fstyp -v /dev/vgfc07/asgr07vxfsversion: 5f_bsize: 8192f_frsize: 2048f_blocks: 262012928f_bfree: 261972575f_bavail: 253785933f_files: 65493168f_ffree: 65493136f_favail: 65493136f_fsid:

Prerequisites Before you start to set up the necessary file systems , carefully plan their distribution to available disks. Decide whether one or more volume groups (VGs) should be used. Procedure 1. Enter the command smitty.2. Select:Physical & Logical Storage → Logical Volume Manager →Volume Groups → Add a Volume Group3. Enter a volume group

You can set up swap space now if you have a suitable volume group. You also can perform this step at the end of the OS preparation. Prerequisites You can find the minimum swap space requirement as per your project documentation. If possible, you should use an entire physical disk as a swap space partition.

1. Log on as user root.2. Add a CD-ROM file system.a. Enter the command smitty.b. Select:Physical & Logical Storage → File Systems →Add / Change / Show / Delete File Systems →CDROM File Systems → Add a CDROM File Systemc. Press F4 to get a list of device names.Select a device name.d. Enter the mount

  Use Using a logical volume manager allows you to distribute partitions (logical volumes) across several disks (physical volumes). The individual logical volumes are grouped together into volume groups. File systems can be larger than physical disks, but not larger than the volume group. Procedure 1. Examine device configuration Enter the command: ioscan -f -C

a. Determine the size of the installed RAM: Run SAM and choose: Performance Monitors –> System Properties —> Memory b. Find out how much swap is currently configured on your system: /usr/sbin/swapinfo 3. Increase the swap space if necessary. You have two options: –> Manually –> Using SAM 4. Verify the paging size and the